Yamaha GTS-1000
From GummyCarbs
1993 - 1994 GTS1000, GTS1000A
Accessories
Exhausts
R1
Some R1 exhausts are a direct swap. Others require adaptation.
Michael Ireton says:
I have installed the R1 cannister on my 94 GTS. IN order to do this you must
do four things:
1)Purchase 2 exhaust pipe reducer bushings, a 2 1/2 od x 2 1/4 id and a 2 1/4 od x 2 id. These will reduce the R1 canister pipe inlet to match the cat outlet on the GTS.
2)Drill out the rivets from the original strap location and slide it down and around to match the GTS mounting hole.
3)I used a flat round bar and a hammer to indent the R1 inlet pipe where the GTS rear brake lever interferes with the
pipe.
Consumables
Tires
Fuel Filter
The OEM fuel filter is expensive and will probably be out of stock at a dealer. Alternatives are:
- Purolator F44661
- AC/Delco GF708
- Fram G6495
According to Bob Taylor, any fuel filter that fits a Mitsubishi Starion (87-89) (Australian) should work.
Spark Plugs
NGK
From the NGK parts finder:
- Standard p/n DPR8EA-9, stock no. 4929, gap 0.035"
- Iridium p/n DPR8EIX-9, stock no. 2202, gap 0.035"
Maintenance
Valve Adjustments
Clearance
Intake
.11 - .20mm
Exhaust
.21 - .30mm
Feeler Gauges
The Genesis 20-valve head requires feeler gauges which are narrower than most. Some people cut down standard gauges, but there is concern that this will leave burrs.
GTS-1000 Mailing List Recommendations
- Rick Davids recommends Draper tapered gauges.
- "Draper is a UK company. Google Draper + 19613 for UK sites that sell them."
- tooled-up.com (UK)
- Metric: 0.05, 0.10, 0.15, 0.20, 0.30, 0.40, 0.50, 0.60, 0.70, and 0.80mm
- Daren mentions Blue Point gauges.
- Bob Johnson mentions official Yamaha feeler gauges for the 5-valve Genesis heads.
- "I got them from Curt Jordan of Jordan Engineering."
- No part number was specified.
- RSROB recommends the 32-blade, tapered Bikemaster feelers, sold through Tucker Rocky, p/n 15-1527.
- p/n 15-1527 $8.95
- 32-blade
- dual marked 0.03mm/0.001” to 1mm/0.040”
- 95mm long taper blades, hardened and polished
- p/n 15-1525 $5.95
- 12-blade
- dual marked 0.203mm/0.008” to 0.660mm/0.026”
- 95mm long taper blades, hardened and polished
- p/n 15-1526 $6.95
- 20-blade
- 0.05-1.0mm
- 100mm long blades, hardened and polished
- p/n 15-1527 $8.95
Other Sources
- Newark P/N 82K5512, Mitutoyo P/N 950-252 tapered feeler gauge, 26 Blades, 3" Long, .0015"-.025", made in USA ($24.85)
- This thread mentions a tapered gauge by Bike Pro.
- "a company called Bike Pro makes a set that just fit into that middle valve on the 5-valve Genesis engines - everything else is too wide"
- Horex tools makes a variety of metric, tapered ("conical") gauge sets:
- 0.03 - 0.10mm, 8 blade, p/n 2608 101
- 0.05 - 0.50mm, 8 blade, p/n 2608 102
- 0.05 - 1.00mm, 13 blade, p/n 2608 103
- 0.05 - 1.00mm, 20 blade, p/n 2608 104 ($9.99 on Ebay)
- 0.05 - 2.00mm, 21 blade, p/n 2608 105
- 0.05 - 1.00mm, 18 blade, p/n 2608 106
- 0.10 - 2.00mm, 20 blade, p/n 2608 107
- 0.10 - 0.50mm, 21 blade, p/n 2608 108
- 0.03 - 1.00mm, 32 blade, p/n 2608 109
Shim Substitutions
This ST1100 page lists bikes with shims interchangeable with the ST1100. Presumably the relationship works both ways...
ABS
- Kevin Hawkin's ABS rebuild guide gives detailed instructions and photos to rebuild a seized ABS pump (archived here).
- Terminals to jump in order to cycle the ABS.
- Links to information about cycling the ABS.
- Advice on pedal travel during ABS cycle (GTS 1000 archive)
- Counter-claim (GTS 1000 Archive)
Front Suspension Lubrication
The dreaded front-end squeak. If you hear the squeak, the bearings in the front swingarm should be disassembled and lubed as soon as possible. If this isn't done in a timely manner, the bearings will eat themselves and are quite costly to replace.
- David Sheldrake's ramblings on greasing the front suspension.
Resources
- The GTS 1000 Mailing List Archive is an invaluable tool.
- Kevin Hawin's web page has the excellent ABS tutorial and information on upgrades.